基于电信号特征分析的电机故障诊断技术

介绍了电机故障诊断技术平台的组成,分析了电机常见故障下电信号的特征。利用宜昌和景洪工厂两台电机进行了实际对比测试,宜昌工厂电机定子电流特征频率在49.2Hz时表现出峰值-36.08dB,在50.8Hz时表现峰值则为-37.23dB,表明电机存在转子断条故障;景洪工厂电机在转子特征频率为113.51Hz时,出现峰值-58.47dB,表明电机存在静态偏心故障。经电机现场抽芯检查,验证了电机故障快速诊断平台给出的电机健康状态评估结果,证实了基于电信号特征分析的电机故障诊断技术的准确性。     

红心火龙果发酵液喷雾干燥工艺优化及红心火龙果籽油的研究

以红心火龙果发酵液作为研究对象,通过优化喷雾干燥工艺制备粉剂,最佳工艺条件为:20%麦芽糊精,进液量:10mL/min,进口温度为120℃,出口温度为65℃;得到的粉剂为紫红色粉末,益生菌含量达到108cfu/g以上,口感酸甜。将发酵后的火龙果籽进行提取,得到的火龙果籽油含有丰富的十六酸、亚油酸和油酸。     

Gluten-free cakes with walnut flour: a technological,sensory, and microstructural approach

Walnut flour (WF), a by-product of walnut oil production, is characterised by high polyunsaturated fatty acids, proteins, and fibre contents and presents suitability for bakery products. However, when using non-traditional ingredients, it is essential to evaluate the effect on the quality properties of the final product. So, this work aimed to assess the impact of WF on the technological, physicochemical, and sensory properties of gluten-free (GF) cakes. WF was added at a flour blend (cassava (CS) and maize (MS) starches and rice flour) at 0, 10%, 15%, and 20%. The results showed that WF modified starch gelatinisation, increased amylose–lipid complex (ALC) content, and made crumbs easier to chew. Besides, the total dietary fibre (TDF) and protein content significantly increased. Cakes with 15% WF presented the highest specific volume (SV) and no differences in overall acceptability with respect to control. Hence, WF is a suitable ingredient for gluten-free bakery products.     

Centrifugally spun carbon fibers prepared from aqueous poly(vinylpyrrolidone) solutions as binder-free anodes in lithium-ion batteries

Aqueous solutions of poly(vinylpyrrolidone) (PVP) of various concentrations (20, 25, and 28 wt%) were successfully spun into fibers by centrifugal spinning. The pristine PVP fibers were annealed and carbonized to produce flexible carbon fibers for use as binder-free anodes in lithium-ion batteries. These flexible carbon fibers were prepared by developing a novel three-step heat treatment to reduce the residual stresses in the pristine PVP precursor fibers, and to prevent fiber degradation during carbonization. The thermogravimetric analysis data showed that the annealed fibers yielded a residual mass percentage of 36.0% while the pristine PVP fibers suffered a higher mass loss and only retained 26.5% of original mass above 450 °C (under nitrogen). The electrochemical performance of the carbon-fiber anodes was evaluated by conducting galvanostatic charge/discharge, rate performance, and cycle voltammetry experiments. The 20, 25, and 28 wt% derived binder-free anodes delivered specific charge capacities of 205, 189, and 275 mAh g⁻¹, respectively, after the first cycle at a current density of 100 mA g⁻¹. The results obtained in this work indicate that a feasible pathway towards a large-scale production of carbon-fiber anodes from a 100% aqueous solution can be achieved via centrifugal spinning and subsequent heat treatment.     

Acidification of the electrolyte during the galvanic corrosion of AA7075: A numerical and experimental study

The electrochemical interactions between aluminum alloy 7075 and low-carbon steels under gelled electrolytes were studied. Such electrolytes provided the opportunity to investigate both thick and thin electrolyte systems. The electrolyte was chemically modified to visually track the acidic fronts during the anodic reaction and the subsequent hydrolysis process. Two mathematical models were validated for both thick and ultrathin electrolytes. The acidification of thick electrolytes was extended some millimeters beyond the aluminum alloy surface, whereas the acidic front was localized next to the metallic joint using ultrathin electrolytes. The combination of both numerical and experimental results allows proving (and explaining why) that the acidification process is more aggressive under dilute than under concentrated electrolytes.     

并流控速沉淀法制备纳米α-Bi2O3及其光催化降解苯酚性能研究

以五水合硝酸铋为铋源,氢氧化钠为沉淀剂,通过简单易操作的并流控速沉淀法合成了α-Bi2O3纳米颗粒.同时,利用XRD和SEM分析了所获产品的结构与表面形貌.并选用苯酚作为模拟污染物,利用LC3000型高效液相色谱仪对其进行色谱分析,探究了所合成的纳米α-Bi2O3光催化剂的催化性能.当苯酚的质量分数为100μg·g?1、pH=8、α-Bi2O3投加量为60 mg·L?1时,可见光照射180 min,降解率可达92.6％.通过自由基捕获实验发现,在α-Bi2O3光催化降解苯酚体系中主要活性物种为羟基自由基.     

白酒人工催陈技术研究进展

白酒自然陈酿具有周期长、占地面积大和投资成本高等问题，因此白酒人工催陈技术受到了广泛的关注。目前白酒人工催陈技术主要包括物理催陈、化学催陈和生物催陈等，其中，物理催陈和生物催陈应用潜力较大，这些技术的应用可以大幅度缩短储存时间，提高白酒品质，降低生产成本。本文从白酒陈酿机理、储存条件出发，综述中国白酒人工催陈技术的研究现状，并对不同的催陈技术及其应用前景进行了分析和比较，旨在为今后白酒人工催陈的研究提供参考和借鉴。     

4,6-二氯嘧啶合成工艺研究

4,6-二氯嘧啶是一种重要的化工中间体.研究了反应温度、溶剂种类、催化剂种类、催化剂用量和反应物投料配比在4,6-二氯嘧啶合成过程中对反应的影响.结果 表明,在以邻硝基甲苯为溶剂,苄基三乙基氯化铵为催化剂,且催化剂用量为4,6-二羟基嘧啶质量的2％,n(4,6-二羟基嘧啶):n(三光气)=1∶0.8,反应温度为100～110℃的最佳条件下,产品收率可以达到93.4％.     

Emerging Plasmonic Assemblies Triggered by DNA for Biomedical Applications

Plasmonic gold nanocrystal represents plasmonic metal nanomaterials, and has a variety of unique and beneficial properties, such as optical signal enhancement, catalytic activity, and photothermal properties tuned by local temperature, which are useful in physical, chemical, and biological applications. In addition, the inherent properties of predictable programmability, sequence specificity, and structural plasticity provide DNA nanostructures with precise controllability, spatial addressability, and targeting recognition, serving as ideal ligands to link or position building blocks during the self-assembly process. Self-assembly is a common technique for the organization of prefabricated and discrete nanoparticle blocks for the construction of extremely sophisticated nanocomposites. To this end, the integration of DNA nanotechnology with Au nanomaterials, followed by assembly of DNA-functionalized Au nanomaterials can form novel functional Au nanomaterials that are difficult to obtain through conventional methods. Here, recent progress in DNA-assembled Au nanostructures of various shapes is summarized, and their functions are discussed. The fabrication strategies that employ DNA for the self-assembly of Au nanostructures, including dimers, tetramers, satellites, nanochains, and other nanostructures with more complex geometric configurations are first described. Then, the characteristic optical properties and applications of biosensing, bioimaging, drug delivery, and therapy are discussed. Finally, the remaining challenges and prospects are elucidated.     

Mechanical properties and thermal shock in thin ZrO2–Y2O3–Al2O3 films obtained by the sol-gel method

Thin multilayer coatings of ZrO₂–Y₂O₃–Al₂O₃ were prepared using the sol-gel method and dip-coating technique in order to advance in the study of what influence the incorporation of Al₂O₃ has on films of Y₂O₃-doped ZrO₂, investigating its role in the synthesis of the solutions and in the characteristics and properties of the coatings. After the characterization of the solutions used in the process, the microstructure of the films was studied and their mechanical behaviour and resistance to thermal shock were determined so as to optimize the characteristics and functionality of these coatings. With increased alumina content, 3YSZ-Al₂O₃ (20 mol%), the cubic phase of the zirconia disappeared completely at the sintering temperature used (700 °C), resulting in the tetragonal phase with Al in solution. There was also a decrease in the coatings' hardness and Young's modulus, and an increase in toughness and resistance to thermal shock. These results allow guidelines to be established for the design of multilayer structures that are, tougher, more resistant, and have improved surface properties.